# SPDX-FileCopyrightText: 2019 ladyada for Adafruit Industries
# SPDX-License-Identifier: MIT

# Example code implementing WPA2 Enterprise mode
#
# This code requires firmware version 1.3.0, or newer, running
# on the ESP32 WiFi co-processor. The latest firmware, and wiring
# info if you are using something other than a PyPortal, can be found
# in the Adafruit Learning System:
# https://learn.adafruit.com/adding-a-wifi-co-processor-to-circuitpython-esp8266-esp32/firmware-files#esp32-only-spi-firmware-3-8

import re
import time

import adafruit_connection_manager
import adafruit_requests
import board
import busio
from digitalio import DigitalInOut

# Use this import for adafruit_esp32spi version 11.0.0 and up.
# Note that frozen libraries may not be up to date.
# import adafruit_esp32spi
from adafruit_esp32spi import adafruit_esp32spi


# Version number comparison code. Credit to gnud on stackoverflow
# (https://stackoverflow.com/a/1714190), swapping out cmp() to
# support Python 3.x and thus, CircuitPython
def version_compare(version1, version2):
    def normalize(v):
        return [int(x) for x in re.sub(r"(\.0+)*$", "", v).split(".")]

    return (normalize(version1) > normalize(version2)) - (normalize(version1) < normalize(version2))


print("ESP32 SPI WPA2 Enterprise test")

# ESP32 setup
# If your board does define the three pins listed below,
# you can set the correct pins in the second block
try:
    esp32_cs = DigitalInOut(board.ESP_CS)
    esp32_ready = DigitalInOut(board.ESP_BUSY)
    esp32_reset = DigitalInOut(board.ESP_RESET)
except AttributeError:
    esp32_cs = DigitalInOut(board.D9)
    esp32_ready = DigitalInOut(board.D10)
    esp32_reset = DigitalInOut(board.D5)

# Secondary (SCK1) SPI used to connect to WiFi board on Arduino Nano Connect RP2040
if "SCK1" in dir(board):
    spi = busio.SPI(board.SCK1, board.MOSI1, board.MISO1)
else:
    spi = busio.SPI(board.SCK, board.MOSI, board.MISO)
esp = adafruit_esp32spi.ESP_SPIcontrol(spi, esp32_cs, esp32_ready, esp32_reset)

pool = adafruit_connection_manager.get_radio_socketpool(esp)
ssl_context = adafruit_connection_manager.get_radio_ssl_context(esp)
requests = adafruit_requests.Session(pool, ssl_context)

if esp.status == adafruit_esp32spi.WL_IDLE_STATUS:
    print("ESP32 found and in idle mode")

# Get the ESP32 fw version number
print("Firmware vers.", esp.firmware_version)

print("MAC addr:", [hex(i) for i in esp.MAC_address])

# WPA2 Enterprise support was added in fw ver 1.3.0. Check that the ESP32
# is running at least that version, otherwise, bail out
assert version_compare(esp.firmware_version, "1.3.0") >= 0, (
    "Incorrect ESP32 firmware version; >= 1.3.0 required."
)

# Set up the SSID you would like to connect to
# Note that we need to call wifi_set_network prior
# to calling wifi_set_enable.
esp.wifi_set_network(b"YOUR_SSID_HERE")

# If your WPA2 Enterprise network requires an anonymous
# identity to be set, you may set that here
esp.wifi_set_entidentity(b"")

# Set the WPA2 Enterprise username you'd like to use
esp.wifi_set_entusername(b"MY_USERNAME")

# Set the WPA2 Enterprise password you'd like to use
esp.wifi_set_entpassword(b"MY_PASSWORD")

# Once the network settings have been configured,
# we need to enable WPA2 Enterprise mode on the ESP32
esp.wifi_set_entenable()

# Wait for the network to come up
print("Connecting to AP...")
while not esp.is_connected:
    print(".", end="")
    time.sleep(2)

print("")
print("Connected to", esp.ap_info.ssid, "\tRSSI:", esp.ap_info.rssi)
print("My IP address is", esp.ipv4_address)
print(f"IP lookup adafruit.com: {esp.pretty_ip(esp.get_host_by_name('adafruit.com'))}")
print(f"Ping google.com: {esp.ping('google.com')} ms")

print("Done!")