# SPDX-FileCopyrightText: 2020 Jerry Needell for Adafruit Industries
# SPDX-License-Identifier: MIT

# Example to send a packet periodically

import time

import board
import busio
import digitalio

# Define radio parameters.
RADIO_FREQ_MHZ = 915.0  # Frequency of the radio in Mhz. Must match your
# module! Can be a value like 915.0, 433.0, etc.

# Define pins connected to the chip, use these if wiring up the breakout according to the guide:
CS = digitalio.DigitalInOut(board.CE1)
RESET = digitalio.DigitalInOut(board.D25)

# Initialize SPI bus.
spi = busio.SPI(board.SCK, MOSI=board.MOSI, MISO=board.MISO)

# Initialze RFM radio
# uncommnet the desired import and rfm initialization depending on the radio boards being used

# Use rfm9x for two RFM9x radios using LoRa

# from adafruit_rfm import rfm9x

# rfm = rfm9x.RFM9x(spi, CS, RESET, RADIO_FREQ_MHZ)

# Use rfm9xfsk for two RFM9x radios or RFM9x to RFM69 using FSK

from adafruit_rfm import rfm9xfsk

rfm = rfm9xfsk.RFM9xFSK(spi, CS, RESET, RADIO_FREQ_MHZ)

# Use rfm69 for two RFM69 radios using FSK

# from adafruit_rfm import rfm69

# rfm = rfm69.RFM69(spi, CS, RESET, RADIO_FREQ_MHZ)

# For RFM69 only: Optionally set an encryption key (16 byte AES key). MUST match both
# on the transmitter and receiver (or be set to None to disable/the default).
# rfm.encryption_key = None
# rfm.encryption_key = (
#    b"\x01\x02\x03\x04\x05\x06\x07\x08\x01\x02\x03\x04\x05\x06\x07\x08"
# )

# for OOK on RFM69 or RFM9xFSK
# rfm.modulation_type = 1

# Disable the RadioHead  Header
rfm.radiohead = False
# set the time interval (seconds) for sending packets
transmit_interval = 5
node = 2
destination = 1
rfm.enable_address_filter = True
rfm.fsk_node_address = node
rfm.fsk_broadcast_address = 0xFF
# For RFM69 only:
# Optionally set an encryption key (16 byte AES key). MUST match both
# on the transmitter and receiver (or be set to None to disable/the default).
rfm.encryption_key = None
# rfm.encryption_key = (
#    b"\x01\x02\x03\x04\x05\x06\x07\x08\x01\x02\x03\x04\x05\x06\x07\x08"
# )

# initialize counter
counter = 0
# send a broadcast mesage
rfm.send(bytes(f"message number {counter}", "UTF-8"), destination=destination)

# Wait to receive packets.
print("Waiting for packets...")
# initialize flag and timer
time_now = time.monotonic()
while True:
    # Look for a new packet - wait up to 5 seconds:
    packet = rfm.receive(timeout=2.0)
    # If no packet was received during the timeout then None is returned.
    if packet is not None:
        # Received a packet!
        # Print out the raw bytes of the packet:
        print(f"Received (raw bytes): {packet}")
        # send reading after any packet received
    if time.monotonic() - time_now > transmit_interval:
        # reset timeer
        time_now = time.monotonic()
        counter = counter + 1
        rfm.send(bytes(f"message number {counter}", "UTF-8"), destination=destination)