# SPDX-FileCopyrightText: 2021 ladyada for Adafruit Industries
# SPDX-License-Identifier: MIT

# Example to send a packet periodically between addressed nodes with ACK
# Author: Jerry Needell
#
import time

import board
import busio
import digitalio

# Define radio parameters.
RADIO_FREQ_MHZ = 915.0  # Frequency of the radio in Mhz. Must match your
# module! Can be a value like 915.0, 433.0, etc.

# Define pins connected to the chip, use these if wiring up the breakout according to the guide:
CS = digitalio.DigitalInOut(board.CE1)
RESET = digitalio.DigitalInOut(board.D25)

# Initialize SPI bus.
spi = busio.SPI(board.SCK, MOSI=board.MOSI, MISO=board.MISO)

# Initialze RFM radio
# uncommnet the desired import and rfm initialization depending on the radio boards being used

# Use rfm9x for two RFM9x radios using LoRa

from adafruit_rfm import rfm9x

rfm = rfm9x.RFM9x(spi, CS, RESET, RADIO_FREQ_MHZ)

rfm.radiohead = False  # Do not use RadioHead Header
# set spreading factor
rfm.spreading_factor = 7
print("spreading factor set to :", rfm.spreading_factor)
print("low_datarate_optimize set to: ", rfm.low_datarate_optimize)
# rfm.signal_bandwidth = 500000
print("signal_bandwidth set to :", rfm.signal_bandwidth)
print("low_datarate_optimize set to: ", rfm.low_datarate_optimize)
if rfm.spreading_factor == 12:
    rfm.xmit_timeout = 5
print("xmit_timeout set to: ", rfm.xmit_timeout)
if rfm.spreading_factor == 12:
    rfm.receive_timeout = 5
elif rfm.spreading_factor > 7:
    rfm.receive_timeout = 2
print("receive_timeout set to: ", rfm.receive_timeout)
rfm.enable_crc = True
# set the time interval (seconds) for sending packets
transmit_interval = 10

# initialize counter
counter = 0
# send startup message from my_node
message = bytes(f"startup message from node", "UTF-8")
if rfm.spreading_factor == 6:
    payload = bytearray(40)
    rfm.payload_length = len(payload)
    payload[0 : len(message)] = message
    rfm.send(
        payload,
        keep_listening=True,
    )
else:
    rfm.send(
        message,
        keep_listening=True,
    )

# Wait to receive packets.
print("Waiting for packets...")
# initialize flag and timer
last_transmit_time = time.monotonic()
while True:
    # Look for a new packet: only accept if addresses to my_node
    packet = rfm.receive()
    # If no packet was received during the timeout then None is returned.
    if packet is not None:
        # Received a packet!
        # Print out the raw bytes of the packet:
        print(f"Received (raw payload): {packet}")
        print([hex(x) for x in packet])
        print(f"RSSI: {rfm.last_rssi}")
        # send reading after any packet received
    if time.monotonic() - last_transmit_time > transmit_interval:
        # reset timeer
        last_transmit_time = time.monotonic()
        # send a  mesage to destination_node from my_node
        message = bytes(f"message from node {counter}", "UTF-8")
        if rfm.spreading_factor == 6:
            payload = bytearray(40)
            rfm.payload_length = len(payload)
            payload[0 : len(message)] = message
            rfm.send(
                payload,
                keep_listening=True,
            )
        else:
            rfm.send(
                message,
                keep_listening=True,
            )

        counter += 1