# SPDX-FileCopyrightText: 2021 ladyada for Adafruit Industries
# SPDX-License-Identifier: MIT

import asyncio
import time

import board
import busio
import digitalio

# Define radio parameters.
RADIO_FREQ_MHZ = 915.0  # Frequency of the radio in Mhz. Must match your
# module! Can be a value like 915.0, 433.0, etc.

# Define pins connected to the chip, use these if wiring up the breakout according to the guide:
CS = digitalio.DigitalInOut(board.CE1)
RESET = digitalio.DigitalInOut(board.D25)

# Initialize SPI bus.
spi = busio.SPI(board.SCK, MOSI=board.MOSI, MISO=board.MISO)

# Initialze RFM radio
# uncommnet the desired import and rfm initialization depending on the radio boards being used

# Use rfm9x for two RFM9x radios using LoRa

from adafruit_rfm import rfm9x

rfm = rfm9x.RFM9x(spi, CS, RESET, RADIO_FREQ_MHZ)

# Use rfm9xfsk for two RFM9x radios or RFM9x to RFM69 using FSK

# from adafruit_rfm import rfm9xfsk

# rfm = rfm9xfsk.RFM9xFSK(spi, CS, RESET, RADIO_FREQ_MHZ)

# Use rfm69 for two RFM69 radios using FSK

# from adafruit_rfm import rfm69

# rfm = rfm69.RFM69(spi, CS, RESET, RADIO_FREQ_MHZ)

# For RFM69 only: Optionally set an encryption key (16 byte AES key). MUST match both
# on the transmitter and receiver (or be set to None to disable/the default).
# rfm.encryption_key = None
# rfm.encryption_key = (
#    b"\x01\x02\x03\x04\x05\x06\x07\x08\x01\x02\x03\x04\x05\x06\x07\x08"
# )

# for OOK on RFM69 or RFM9xFSK
# rfm.modulation_type = 1

# set node addresses
rfm.node = 1
rfm.destination = 100
# send startup message from my_node
rfm.send_with_ack(bytes(f"startup message from node {rfm.node}", "UTF-8"))
rfm.listen()
# Wait to receive packets.
print("Waiting for packets...")
# initialize flag and timer


# pylint: disable=too-few-public-methods
class Packet:
    """Simple class to hold an  value. Use .value to to read or write."""

    def __init__(self):
        self.received = False


# setup interrupt callback function
async def wait_for_packets(packet_status, lock):
    while True:
        if rfm.payload_ready():
            if lock.locked():
                print("locked waiting for receive")
            async with lock:
                packet = await rfm.asyncio_receive_with_ack(with_header=True, timeout=None)
            if packet is not None:
                packet_status.received = True
                # Received a packet!
                # Print out the raw bytes of the packet:
                print(f"Received (raw bytes): {packet}")
                print([hex(x) for x in packet])
                print(f"RSSI: {rfm.last_rssi}")
        await asyncio.sleep(0.001)


async def send_packets(packet_status, lock):
    # initialize counter
    counter = 0
    ack_failed_counter = 0
    counter = 0
    transmit_interval = 5
    time_now = time.monotonic()
    while True:
        # If no packet was received during the timeout then None is returned.
        if packet_status.received:
            packet_status.received = False
        if time.monotonic() - time_now > transmit_interval:
            # reset timeer
            time_now = time.monotonic()
            counter += 1
            # send a  mesage to destination_node from my_node
            if lock.locked():
                print("locked waiting for send")
            async with lock:
                if not await rfm.asyncio_send_with_ack(
                    bytes(
                        f"message from node {rfm.node} {counter} {ack_failed_counter}",
                        "UTF-8",
                    )
                ):
                    ack_failed_counter += 1
                    print(" No Ack: ", counter, ack_failed_counter)
        await asyncio.sleep(0.1)


async def main():
    packet_status = Packet()
    lock = asyncio.Lock()
    task1 = asyncio.create_task(wait_for_packets(packet_status, lock))
    task2 = asyncio.create_task(send_packets(packet_status, lock))

    await asyncio.gather(task1, task2)  # Don't forget "await"!


asyncio.run(main())